one、 Overview
Fast alkaline etchant sec-onetwenty-nine# is a copper ammonia etchant, which has the advantages of simple control, stable operation, high copper dissolution, small side corrosion, fast etching speed and so on. It is widely used in printed circuit technology with gold nickel, tin, dry film, liquid photosensitive ink and some printing ink as protective layer.
Fast alkaline etchant sec-onetwenty-nine # is based on the original ec-3two8 # to enhance the regeneration ability, increase the etching speed by 30%, and completely avoid the formation of sediment.
Fast alkaline etchant sec-onetwenty-nine# series products include:
one、SEC-onetwenty-nine#Etching salt.
two、SEC-onetwenty-nine#Etching (replenishment) solution: sec-onetwenty-nine per one00 liters#Etching salt two8KG, ammonia 45L and water.
3、SEC-onetwenty-nine#Etching additive: add one-two% as needed to maintain the etching speed and prevent deposition.
two、 Technical indicators(SEC-onetwenty-nine#Etching salt)
one、性狀:白色細小粉末,易溶于水,在溶解過程中會吸收熱量。
two. Etching coefficient: two.50 (spray method)
3. Etching speed: about 3.0 mil / min (50 ℃), pH = 8.9, two.5kg/cmtwoone.twotwo0Kg/L)
4. Operating parameters of working fluid:
Temperature 45-55 ℃
PH 值 8.two—8.9
密度 one.two00—one.two30
銅含量one50—one80g/L
氯含量one60—one80g/L
3、 Packaging and storage
one、包裝:two5公斤、two8公斤。
two、貯存:宜放在通風良好,乾燥及遠離熱源的環境中。
4、 Equipment
The parts of relevant equipment in contact with etching solution shall be made of alkali resistant chemical erosion resistant materials such as polyvinyl chloride, polypropylene, polyethylene or stainless steel. When using synthetic materials, it is necessary to operate at the temperature that the material can tolerate to prevent deformation. Good sealing can not only reduce the escape of ammonia in the solution, but also improve the environment of the workplace.
The ventilation system should be as few as possible, as long as it can maintain a little negative pressure so that ammonia does not pollute the air in the workplace. Excessive air extraction will cause excessive escape of ammonia in the working fluid, resulting in unstable operating conditions, sediment deposition and low speed.
5、 Preparation of make-up liquid
one、補充液的組成:SEC—onetwenty-nine#蝕刻鹽two8 % (W/V)
two5% 氨水 45 % (V/V)
two、配製步驟(以one00升爲例):在密封性能良好的配液容器中,加入SEC—onetwenty-nine#蝕刻鹽two8公斤後,立即加入60℃左右的溫水約50升,攪拌約two0分鐘,此時大部份粉劑溶解且溫度已經降至室溫,再加入two5%氨水45升,繼續攪拌,直到粉劑完全溶解。最後補充水到one00升。
3. Parameters of make-up liquid:
密度one.0two—one.03
PH value 9.6-9.9
氯含量one60—one70g/L
6、 Working fluid control method
one、操作:放掉蝕刻槽中工作母液one0—two0%,注入等體積補充液,即得到工作液?;蚴褂每刂泼芏鹊淖詣犹砑酉到y(tǒng)自動補充,控制密度調校在one.twotwo0。
two、調整:Low pH value indicates that the ammonia content in the solution is insufficient, which may lead to copper ion deposition. The pH value can be improved by supplementing ammonia or supplement solution; If the pH value is too high, it will increase the escape of ammonia, waste materials and make the workplace environment bad.
The copper content can be roughly reflected by the solution density value. Too low or too high will slow down the etching speed. If the density does not rise to a reasonable level, it is often accompanied by the phenomenon of too low pH value (insufficient ammonia content).
7、 Laboratory analysis
According to the general test method of copper ammonia complex. The company and dealers can also provide customers with free testing services.
8、 Explain/Sediment problem:
本公司同時提供商品SEC-onetwenty-nine補充液,就近供應給周邊客戶。
The slurry deposition in the working solution is mainly the hydrate of the double salt of cuprous chloride and ammonium chloride. After the deposition is formed, not only the etching speed is reduced, but also the nozzle is blocked. Because it cannot be stirred in the etching machine, this kind of sediment is difficult to dissolve once it is formed, so the formation of sediment must be prevented.
The way to prevent deposition is to ensure sufficient oxidation capacity to maintain the Cu + concentration at a low level. This is also the control method of various commercial etchants.
本産品品質可與任何品牌的蝕刻劑比較;是一種質優、價廉、使用方便的蝕刻劑。選擇SEC-onetwenty-nine#將給您帶來豐厚的回報。
03-03
Sec-066 cleaning agent
Plate washing waterSEC-66eight#The main components areDimethoxymethane, dichloromethane and methanol,It has excellent physical and chemical properties, i.e. good solubility, low boiling point and good
03-03
S-655 developer
DeveloperS-655#It is a kind of anti welding ink specially used for high quality requirements/線路干膜使用的Developer,主要成分by高純度的碳酸鉀及溶纖劑、軟水劑、非silicon型消泡劑等高級原料。This producthaveHave excellentAnalytical abilityan
03-03
158# film cleaner (without n-hexane)
Film cleanerSEC-one5eight#It is a quick drying electrostatic cleaning agent composed of low boiling solvent. It is suitable for cleaning and removing static electricity of various silver salt films (b
03-03
155# film cleaner (flame retardant)
Film cleanerSEC-onefivefive#It is a quick drying electrostatic cleaning agent composed of low boiling solvent. It is suitable for cleaning and removing static electricity of various silver salt films